[Jul 30, 2024] Pass Fortinet NSE6_FSW-7.2 Exam Info and Free Practice Test
NSE6_FSW-7.2 Exam Dumps PDF Updated Dump from DumpsTorrent Guaranteed Success
NEW QUESTION # 18
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?
- A. FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.
- B. Register FortiSwitch to FortiSwitch Cloud to save a copy before managing with FortiGate.
- C. Enable the FortiLink setting on FortiSwitch before the authorization process.
- D. Use a migration tool based on Python script to convert the configuration.
Answer: B
NEW QUESTION # 19
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
- A. Loopback interfaces
- B. Switch virtual interfaces
- C. Detected management interfaces
- D. Physical interfaces
Answer: A,B
NEW QUESTION # 20
What type of multimode transceiver can be used to split a 40G port?
- A. SFP transceiver
- B. QSFP transceiver
- C. QSFP+ transceiver
- D. SFP+ transceiver
Answer: C
NEW QUESTION # 21
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?
- A. DTLS client hello had the incorrect pre-shared key.
- B. FortiSwitch has disabled FortiLink and is only managed as a standalone.
- C. The CAPWAP tunnel failed to come up due to a mismatch in time.
- D. The handshake process timed out before FortiSwitch responded.
Answer: C
NEW QUESTION # 22
What are two ways in which automatic MAC address quarantine works on FortiSwitch? (Choose two.)
- A. MAC address quarantine can be enabled through the FortiGate CLI only.
- B. FortiAnalyzer with a threat detection services license is required.
- C. FortiGate applies the quarantine-related configuration only on FortiGate.
- D. FortiSwitch supports only by VLAN quarantine mode.
Answer: A,B
NEW QUESTION # 23
Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?
- A. Power management
- B. Network policy
- C. Inventory management
- D. Location
Answer: C
NEW QUESTION # 24
How is traffic routed on FortiSwitch?
- A. Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.
- B. Hardware-based routing on FortiSwitch is handled by the CPU.
- C. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).
- D. ASIC hardware routing can only handle dynamic routing, if supported.
Answer: C
NEW QUESTION # 25
How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?
- A. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces.
- B. FortiGate configures and enables egress sampling on all management interfaces.
- C. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.
- D. FortiGate configures and enables flow sampling on FortiSwitch but does not change existing sampling settings of interfaces.
Answer: A
NEW QUESTION # 26
What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?
- A. FortiGate multi-tenancy
- B. FortiGate clustering protocol
- C. FortiLink split interface
- D. Multi-chassis link aggregation trunk
Answer: A
NEW QUESTION # 27
Exhibit.
port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)
- A. You must add port24 native VLAN as an allowed VLAN on internal.
- B. You should use VLAN ID 4094 as the native VLAN on port24.
- C. You must allow VLAN ID 4094 on port24, if management traffic is tagged.
- D. You must add VLAN ID 200 to the allowed VLANS on internal.
Answer: B,C
NEW QUESTION # 28
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The port full speed prior the split was 100G SFP+
- B. The split port can be assigned to native VLAN
- C. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- D. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
Answer: C,D
NEW QUESTION # 29
Exhibit.
You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.
- A. The system time is not in-sync and is using a non-default value
- B. The management mode was set to use FortiLink mode.
- C. Switch auto-discovery is enabled.
- D. The FortiSwitch device is scheduled to reboot as part the authorization process
Answer: B
NEW QUESTION # 30
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?
- A. FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.
- B. Allowed VLANS expand the collision domain to the port.
- C. Untagged VLANs must be part of the allowed VLANs: ingress and egress.
- D. The native VLAN is implicitly part of the allowed VLAN on the port.
Answer: D
NEW QUESTION # 31
Refer to the configuration:
Which two conditions does FortiSwitch need to meet to successfully configure the options shown in the exhibit above? (Choose two.)
- A. FortiSwitch would need to be rebooted.
- B. The split port can be assigned to a native VLAN.
- C. The FortiSwitch model is equipped with a maximum of 54 interfaces
- D. The Dort full speed prior to the split was 100G QSFP+.
Answer: A,C
NEW QUESTION # 32
In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)
- A. Switch the FortiLink interface to the target VDOM.
- B. Create a virtual port pool on the FortiGate CLI.
- C. Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.
- D. Assign a port to a VDOM directly on the managed FortiSwitch.
Answer: B,D
NEW QUESTION # 33
Which QoS mechanism maps packets with specific CoS or DSCP markings to an egress queue?
- A. Marking for ingress traffic
- B. Classification for ingress traffic
- C. Rate limiting for egress traffic
- D. Queuing for egress traffic
Answer: B
NEW QUESTION # 34
Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?
- A. The monitoring device must be connected to the same switch where the traffic is being mirrored
- B. SPAN can be configured only on a standalone FortiSwitch.
- C. Mirrored traffic can be sent across multiple switches.
- D. Traffic on the management interface can be mirrored and captured by the monitoring device.
Answer: D
NEW QUESTION # 35
What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?
- A. FortiGate will automatically save the existing FortiSwitch configuration during the Forti-link management process.
- B. Use a migration tool based on python script to convert the configuration
- C. Enable the Forti-link setting on FortiSwitch before the authorization process
- D. Register FortiSwitch to For1ISwitch Cloud to save a copy before managing by Forti-Gate.
Answer: C
NEW QUESTION # 36
Exhibit.
LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)
- A. Switch 3 and Switch 4 uplinks are treated as single interfaces.
- B. Switch 1 and Switch 2 both seen as one single switch.
- C. Switch 3 and switch 4 are seen as one MCLAG switch client
- D. Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group
Answer: B,C
NEW QUESTION # 37
Refer to the exhibit.
Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)
- A. FortiSwitch is sending FortiLink heartbeats to FortiGate.
- B. FortiSwitch is discovered and authorized by FortiGate.
- C. FortiSwitch is ready to push its new hostname to FortiGate.
- D. FortiSwitch is in a waiting state to join the stack group on FortiGate.
Answer: A,B
NEW QUESTION # 38
Exhibit.
port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)
- A. Oport1 was shut down by loop guard protection.
- B. STP triggered a loop and applied loop guard protection on port1.
- C. An endpoint sent BPDU on port1 it received from another interface.
- D. Loop guard frame sourced from port 1 was received VLAN 10 ports.
Answer: A,D
NEW QUESTION # 39
......
Pass Your Fortinet Exam with NSE6_FSW-7.2 Exam Dumps: https://braindumps2go.dumpstorrent.com/NSE6_FSW-7.2-exam-prep.html